Showing posts with label Home and House. Show all posts
Showing posts with label Home and House. Show all posts

Friday, April 4, 2008

Trucker's Hitch

Trucker's Hitch

Aplications : This hitch gives tension to the lashing on a loaded vehicle. (See also diamond hitch)

Method : Treble the rope parts in your hand and hook an overhand loop onto the uppermost bight (1). A trade trick is to put one or two twists into the long bight (2) before doing anything else, to prevent the knot from spilling as you pull it taut and take up the slack (known as swigging). Now pull a bight of the free line through the twisted bight, pass it around a convenient anchorage, and pull (3). Lead the line around the next anchorage point and repeat the process.



History : The other name for this contrivance is the waggoner's hitch, which implies that it is as old as carts and carriages. The first part of the knot (1) is the bell‑ ringer's knot, described as early as 1815.

Chain Stitch Lashing

Chain Stitch Lashing

Aplications : This technique is ideal for securing a range of soft and awkward long bundles, from rolled carpets to furled sails. There is give and take in the embrace of the lashing, and it is therefore suitable for loads that bend and flex.

Method : This technique needs a long rope or cord. Start with a timber hitch (1 and see Killick Hitch). Loop one bight through the other, finishing off with a clove hitch (2-3, and see Clove Hitch). Untie the clove hitch, withdraw the end, pull and watch it unravel.

Marline Hitching

Marline Hitching

Aplications : Although at first glance marline hitching is identical to half-hitching ,there is a little more tying involved than in half-hitching, but this method of securing a parcel gives a better grip.

Method : Unlike half-hitching, which is a series of single hitches, marline hitching uses simple overhand knots tied along the length of the object(s) to be parcelled. Note that a working end is needed for marline hitching, although not for half-hitching. It is tricky to discern the subtle difference between these two techniques just by looking; but slide half-hitches off their bundle and they fall apart, whereas marline hitches end up as a series of overhand knots.

Half Hitching

Half Hitching

Aplications : A simple way to tie long parcels, half-hitching is closely akin to marline hitching.Many people cannot tell the difference, but there is one. Half-hitching can be done without resort to the end of the string or cord used. (See also chain stitch lashing)


Method : Using a continuous line, start with a clove, rolling or timber hitch (see Killick Hitch, Clove Hitch, Rolling Hitch). Add as many hitches at suitable intervals as necessary. Either pass the working end around and through each time, or (with an inconveniently long line) simply slide underhand loops over the end of the bale or parcel as you go.Tie off as you like.



Pole Hitch

Pole Hitch

Aplications : The pole hitch is a gathering and binding knot. A pair of these will hold assorted long objects.

Method : Arrange the cord in an S- or Z-shape beneath the assembled objects, and tuck both ends through opposite bights (1). Draw tight and tie off with a reef knot (2).



History : In 1987 this hitch was recommended by the Girl Guides Association for lashing tent poles together. (See Knotting for Guides by Hazel Bailey.)

Highwayman's Hitch

Highwayman's Hitch

Aplications : A temporary tether for an animal or for mooring a boat, the highwayman's hitch may be tied in the bight of a middled rope, so that a long end is within reach to undo it again. This knot can be used to hold almost anything that will have to be released quickly or awkwardly (e.g., with one hand, or with the teeth, or from a distance).

Method : This is the ultimate in draw-loop knots, tied simply by making one loop on top of another (1-4).



History : There is no evidence to substantiate the reputation of the highwayman's hitch as a quick-get-away knot for robbers on horseback.

Pile Hitch

Pile Hitch

Aplications : This hitch is used for making a line fast to a stake, post, pile or bollard. It is best tied in the bight.

Method : Take a turn with a bight beneath the standing part and place it over the post, etc. (1-3).

Icicle Hitch

Icicle Hitch

Aplications : The icicle hitch can attach a line to the smoothest of spars or rails (including a polished brass fireman's pole), even when it tapers towards the direction of pull.

Method :
A. End of spar accessible

Take at least four turns around the rail or spar (1); take more if an exceptionally secure hitch is required. With the working end, create a generous loop hanging down behind the standing part (2). Pass this loop in front of all other parts and drop it, without twisting, over the end of the spar (3). Draw everything up tight by pulling first the standing part and then the working end at right-angles to the spar. Now tighten it all again. Only then can the load be carefully applied, and the knot pulled out to the shape shown (4). There must be no separation of the two turns on the thicker part of the spar. If this occurs, add extra turns at the start. As long as two turns on the thicker part remain snug together, the hitch should hold fast.

B. End of spar inaccessible
Using the working end, assemble the knot as shown (5-8), but then tighten it until it behaves as already detailed in A above.

History : An ex-tended pile hitch (see p. 72), the icicle hitch was devised by John Smith of Surrey, England. He demonstrated his knot's quite exceptional grip in May 1990 at the eighth Annual General Meeting of the International Guild of Knot Tyers, held at the training ship Steadfast, a Sea Cadet shore establishment at Farnham in Hampshire. Smith hung by this hitch from a splicing fid, which was suspended, point down, from the ceiling.


Scaffold Knot

Scaffold Knot

Aplications : This is a tough noose knot, which may be protected against wear due to chafing by the insertion of a plastic or metal lining called a thimble, creating what sailors refer to as a 'hard eye: Thimbles come in a range of sizes and are obtainable from boat and yacht chandlers. Practised fingers can tie the scaffold knot in 30 seconds or less.


Method : First make the loop and tighten the sliding knot (1-3). Next, insert the thimble (4). See that its jaws bed down into the throat of the noose and pull the whole lot snug. To attach a line directly to a ring or bracket, without using a shackle, fix the thimble in place and pass the working end of the line around it before tying the knot.



History : The scaffold knot was described in Denis Diderot's Encyclopedie of 1762.

Tuesday, April 1, 2008

Boa Knot

Boa Knot

Applications : The ultimate binding, this neatly combines the forms and functions of both constrictor and strangle knots. It may be tied in the same size of cord around a wide range of diameters, wherever seizing or lashing is needed.

Method : Lay down two right-handed, overhand loops, one on top of the other (1-2).Then simply twist the resulting coil into the figure eight layout shown, and slide the knot onto its foundation (3). Draw it up snug, neatening any misaligned cord parts as you do so (4).The knot will usually be tied in the bight like this. It may be formed with a working end by first tying a basic constrictor knot (5) and then wrapping and tucking one of the ends as shown (6-7).



History : This — the newest knot in the book — was discovered in 1996 by Dr Peter Collingwood, the eminent weaver and craft writer, in his search for a reliable seizing on ends which had to be cut very short; and it is a nice example of how knots emerge to fill what (with hindsight) is an obvious gap in the family tree but was previously an overlooked and unsuspected missing link.

Saturday, March 29, 2008

Round turn and two half-hitches

Round turn and two half-hitches

Applications : This is a classic old hitch for securing a line to a ring, rail or to a spar.

Method : Use the friction of the round turn (1) to snub and hold the load; then add the two identical half-hitches (2-3).The two half-hitches have a breaking strength of 60-75%, but the round turn may increase that percentage.



History : In 1794 David Steel referred to this hitch (by the same name) in Elements and Practice of Rigging and Seamanship.

Buntline Hitch

Buntline Hitch

Applications : The buntline hitch was traditionally used to secure a lanyard to a cringle, eyelet, ring or swivel. These days it is also used on tools with small holes in their handles. Note the short end trapped on the inside of the knot (3).This is not recommended in cases where the hitch needs to be undone easily, because it is likely to jam and resist the efforts of fingers to free it. However, where something more secure than the normal two half-hitches is needed, the buntline hitch is useful. When tied in a strip of material, it turns out to be the common knot used for men's neckties (one of life's lesser-known trivial facts).

Method : Make two half-hitches, tying the second inside the first (1-3).



History : The buntline was attached to a sail's footrope, then passed up in front of that sail to a block on the yard, from where it could be used to pull the bottom of the sail up and so spill the wind out of it. As the sail was going to flap about a lot, a very secure knot was needed.

Snuggle Hitch

Snuggle Hitch

Applications : Useful for attaching a line to a spar or rope, the snuggle hitch is stronger than either the clove or rolling hitches . It may be used with a right-angled or a lengthwise pull.

Method : For a lengthwise pull, ensure that the two adjacent wrapping turns are on the same side of the standing part as the load (1-3). Once the load is released, the knot may be untied by either pulling or prising loose the part arrowed (4).The working end can then be withdrawn.



History : The snuggle hitch was devised by Owen K. Nuttall of West Yorkshire, England, and was first published in Knotting Matters in January 1987.

Rolling Hitch

Rolling Hitch

Applications: A close relation of the clove hitch, the rolling hitch attaches a cord to a rope for a lengthwise pull. For smooth rails or spars, consider using the icicle hitch .

Method : Begin as for the clove hitch (1) but take two adjacent diagonal turns on the side of the knot from which the pull will come (2-3). Take care to lock the second diagonal turn inside the first one, i.e., alongside the standing part of the line.



History : This knot was known in earlier days as Magner's hitch or the Magnus hitch.

Clove Hitch

Clove Hitch

Applications : This simple but versatile knot will moor a small boat, suspend a fender or attach any line to a post, rail or ring when the pull is a steady one at right-angles to the point of attachment. However, simplicity has its shortcomings. If pulled around, the clove hitch can work loose. Perversely, it can also jam when wet. Its breaking strength is variously quoted as between

Method : This knot can be tied by tracing a letter N (or its mirror image) with the working end (1-2). For a temporary task, such as hanging a fender, leave a draw-loop (3). Stepping ashore from a slow-moving boat, first cast an underhand loop onto a bollard and use the friction to check the momentum; then, once the line is the length you want it, simply drop the second loop onto the first. Add a half-hitch for extra security.To ensure the direction of pull on a mooring painter does not vary, bring it ashore around a stanchion or other convenient fixed point before attaching it to a post or rail.



History : An old treatise referred to this knot as a builder's knot. William Falconer may have been the first to name it the clove hitch in his Universal Dictionary of the Marine (1769). Aboard ship it was used to secure ratlines to shrouds, creating those rope ladders up which sailormen scrambled to man the yardarms.

Friday, March 28, 2008

Knute Hitch

Knute Hitch

App;ications : Use the Knute hitch to attach a line to anything with a hole not much larger (for obvious reasons) than twice the diameter of the cordage used. This hitch is often tied to fix lanyards to knives and other tools. Europe's largest sailing school, in Poole Harbour, England, uses it to attach the main halyards to the mainsails on its Wayfarer dinghies, no doubt saving on the cost of shackles lost overboard from wet, cold and inexperienced fingers.

Method : Thread a bight and trap the working end with it (1), finishing off either with a stopper knot or with one of those big plastic beads sold in yacht chandlers (2).



History : US master ringger, writer and broadcaster Brion Toss named this hitch in 1990 but it is probably centuries old

Sheet Bend

Sheet Bend

APPLICATIONS :The sheet bend is a general-purpose bend for uniting two lines made of the same material. It may also be used to attach an end to a loop or small eye. It does, however, have a number of limitations. It will jam under a heavy load and, without an extra tuck, can slip in smooth materials. Security tests have shown it to spill after an average 22 tugs out of 100, and it is not a very strong knot, with a breaking strength of 55%.

METHOD: As a general rule, aim to keep both short ends on the same side (1-3). Leave a draw-loop if you prefer (4).For ropes of different size, composition or wetness, use the double sheet bend (5), when the smaller and more flexible cordage makes the double turn around the thicker bight. If the knot is to be subjected to rough treatment, consider reinforcing it with a backward tuck (6), which also makes it more streamline and easier to pull one way through narrow gaps. Swedish marine writer and artist Frank Rosenow spotted a sheet bend in Greek cruising waters used as a bridle for three converging ropes (7).



History : The sheet bend was probably known by Neolithic people; remnants of Stone Age nets have been found with mesh knots resembling sheets bends. David Steel referred to it by this name in Elements and Practice of Ringging and Seamanship (1794), when it was tied in a sheet (i.e., a bit of running ringging to trim a sail). Many knot experts campaign against the use of this bend for lines of different size, pointing out that (if they are too dissimilar) a thick and stiff rope could straighten out and spill the small cord. While this is a fair criticism, the sheet bend -if used sensibly- cannot simply be dismissed.

Fisherman's Knot

Fisherman's Knot

Applications : This is - strictly speaking - a strong and secure bend to join two similar ropes.

Method : Lay the two working parts alongside and parallel to one another (1).Tie an identical overhand knot around each standing part with the other working end (2-3). Pull them together (4-5).



History : In the early nineteenth century, fishermen referred to this knot as the water knot. It has also been known as the angler's knot, the English knot, the Englishman's knot, the true lover's knot and the waterman's knot. The author Captain Marryat wrote of it in his novel Peter Simple (1834); '.... there is a moral in that knot .... that points out the necessity of pulling together .... when we wish to hold on.'

Bowline In The bight

Bowline In The bight

Applications : In these litigious, health-and ­safety conscious times, I do not recommend any ad hoc rope slings and chairs for working aloft or over the side. There are tested and certificated ladders and stages and harnesses for the well prepared. But all sailors sooner or later are faced with some urgent improvisation. This is one such knot, which can be used for lowering an injured person and other emergencies. One leg is put through each loop and the patient (if conscious and capable) holds tight onto the rope at chest level, or is somehow secured to it. It reduces the strength of the line in which it is tied by up to 40%.

Method : As this knot is usually tied in the middle of a rope, it must be made without using either end. The early stages are done with a doubled end (1).The trick is then to pass the bight right over the pre­formed knot (2-3).



History : This knot was illustrated in 1795 by Johann R. in his Allgemeines Worterbuch der Marine. In 1808 it was mentioned as the 'bowline upon the bight' by Darcy Lever, Author of Sheet Anchor.

Bowline

Bowline

Applications : Neither a bend nor a hitch, the bowline (say 'boh-linn') is a knot that makes a fixed loop. It is far from the strongest loop knot, reducing the breaking strength of any stuff in which it is tied by as much as 40%. Nor is it very secure, particularly when the rope is stiff or slippery, when it has been known to capsize (if excessively loaded) or alternatively to spring or shake itself apart (when unloaded).Nevertheless the bowline can be used for a wide range of jobs, from securing the string before tying a parcel, to outdoor pursuits such as climbing. When I was a Metropolitan Police frogman in the 1960s, my colleagues and I tied the line around our waists with a simple bowline. The working end (deliberately made long) was then tucked several times around the adjacent part of the loop to secure it. Climbers' manuals advise their readers to finish off such tucks with one or two half-hitches (made in the opposite direction to the twist) for even greater

Methods : Make it by the so-called sailor's method with a fluent, one-handed twist of the wrist (1-5).You should also work out how to tie a bowline viewed from an unfamiliar angle (6-7). Imagine facing someone, passing a rope around behind them, beneath their armpits, then having to make the knot. See what I mean? The trick is to first take a turn around the standing part of the rope with your working end. Next, pull it out straight to transfer the underhand loop in the standing part. Finally, pass and tuck the working end to lock off in the usual way.If the knot will have to withstand rough treatment, tie the double bowline (8-9). This is therefore stronger and far more secure than a basic bowline



History : Stone Age en knew the sheet bend, which has an identical layout to the bowline, the only difference being which end is used where and for what. There is, however , no evidence of the bowline having been used that far back in the time. It was mentioned as a seafarer's knot by Sir Henry Mainwaring in The Sea-man's Dictionary (1644) and first illustrated in David Steel's Elemants and practice of Ringging and Seamanship in 1794. The time is long gone when it really was a 'bow line knot', used to hold the weather leech of a square sail forward closer to the wind, preventing it being pulled back. Other nautical uses include looping a boat's painter or ship's mooring rope around a quayside bollard, and tying a line around a crewman's waist, to lower him over the side. Two interlocked bowlines also form a handy hawser bend. Some useful variants on the common bowline (e.g., a double bowline, a bowline in the bight and a couple of triple bowlines ). All however, rely upon you first mastering the basic knot.

Template by - Abdul Munir | Daya Earth Blogger Template